SGI Ethernet Card Guide d'installation

10.SGI Origin 3000 L3 Controller...

105. In the Size (Megs) field in the popup window, type the partitionsize from Table 2 for the partition selected.Note: Be sure to select the Grow to fi

119. Click the option button that precedes each partition that youconfigured in step 1 (see Figure 4).Note: <Swap Partition> is automatically pre

1210. Click Next to format the selected partitions.Note: Click the Check for bad blocks while formatting optionbutton if you want to scan the workstat

132. Click the Configure using DHCP option.3. Click the Activate on boot option.4. If you have no additional Ethernet cards or ports of this type tocon

145. To configure an optional Ethernet card or port that connects to theL2 controllers via DHCP protocol, begin by clicking the tab thatcorresponds to

15Configuring the AccountTo configure the account, follow these steps:1. Use the scroll bar to locate your time zone in the available list. ClickNext to

16workstation and monitor configuration may require other settings. Youmay manually input these settings if the option you require is notdisplayed.1. S

17Installing Red Hat Linux 6.2To install Red Hat Linux 6.2, follow these steps:1. Click Next in the About to install window to begin the Red HatLinux

18Installing the Auxiliary Linux SoftwareTo enable the L3 controller solution to function, you must install thefollowing auxiliary Linux software comp

19Installing the L3 Controller SoftwareThe L3 controller software consists of the following components:• Kernel software• L3 driver• L1/L2 firmware uti

2Installation OverviewTo install an SGI Origin 3000 series L3 controller, you must do thefollowing:1. Read the software installation requirements so t

204. Enter the following command to load the diagnostic software:# l3_install5. Remove the SGI Origin 3000 series L3 controller CD-ROM.6. Reboot the s

21Connecting the Workstation Running L3 ControllerSoftware to the SGI Origin 3000 Series SystemThis section describes the following ways to connect a

22This section covers the following topics:• Connecting the workstation to a C-brick console port.• Connecting the workstation to a C-brick L1 port.Co

235. Type cu -l ttyS0 -s 38400 at the Linux prompt. The L1responds with “Connected” as shown:$ cu -l ttyS0 -s 38400Connected.6. Press the Enter key to

24Figure 6 Connecting the Workstation to an SGI Origin 3200 C-brickSerial connectionUSB connectionC-brickConsole port(serial connector)Null modemseria

25Connecting the Workstation to an SGI Origin 3000Server That Has L2 Controller HardwareThis section describes how to connect a Silicon Graphics 230 v

263. Reboot or restart the L3 network by entering the following at theLinux prompt:/etc/rc.d/init.d/network stop/etc/rc.d/init.d/network start4. Be su

27Figure 7 Connecting the Workstation to an SGI Origin 3000 with anL2 ControllerL2 controller with Ethernet hubStandardEthernetcableRear viewEthernet

28©2001, Silicon Graphics, Inc. All rights reserved; provided portions may becopyright in third parties, as indicated elsewhere herein. No permission

3Note: Your Silicon Graphics 230 visual workstation must have Internetand network access if you want to download software directly to theworkstation.S

4• IP address, netmask, network and broadcast addresses• Formatted floppy disk (DOS format)Configuring Red Hat Linux 6.2This section covers the followin

53. Insert the Red Hat Linux 6.2 CD-ROM into the workstation drivebay.4. Using the arrow keys, select CD-ROM from the Boot menu.5. Press the Enter key

64. Click the Enable Dead Keys option button to enable non-Englishkeyboard characters such as umlauts. Click Next to continue.5. Use the arrow keys to

7Note: Do not select the Use fdisk option on the Install Optionsmenu.Figure 1 Install Options Window2. Create partitions and configure the workstation,

8Creating Partitions and Configuring the WorkstationTo create partitions and configure the workstation, follow these steps:1. Click the Manually partiti

92. To configure a workstation drive partition (three are required),begin by clicking Add in the Disk Druid Partitions window, whichbrings up a popup w