SGI Octane III Guide de l'utilisateur Page 14
- Page / 78
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
2 007-5630-001
1: Introduction and Overview
Quick Setup Procedures
Use the information in the following subsections to get your Octane III unpacked, set up and
working in your office or lab environment. If your system ships with hardware, software or media
not listed in this guide, please see its accompanying documentation for installation instructions.
Unpacking the System
Open the SGI Octane III system packaging container and inspect all shipped items for evidence
of mishandling during transit. If the contents appear damaged, file a damage claim with the carrier
immediately.
Caution: To avoid personal injury when unloading the system, use two people when rolling the
system off the shipping pallet. The system can weigh up to approximately 178 pounds (81 kg).
Use the following steps and Figure 1-1 on page 3 to properly unpack your Octane III system:
1. After you have cut the package banding and opened the top, remove the wood ramp and
place it near the front of the pallet, then pull out and remove the two cushioned top pads.
2. Check that the following items are included and note that a DVD-RW drive and
monitor/keyboard/mouse may come as separately packaged options:
• SGI Octane III deskside system
• System power cords
• Silicon Graphics or 3rd party software CDs
• SGI Octane III Deskside Workstation User’s Guide (this document)
3. Remove any items packaged at the top of the box, then pull up the corrugated sleeve and lift
off the anti-static plastic cover.
4. Extract the two bolts that hold the front brace to the shipping pallet assembly and remove it.
5. Align the two bolt holes on the end of the ramp (removed in step 1) with the holes on the
front of the shipping pallet, then push the bolts into place to secure the ramp.
6. Use two people to slowly roll the Octane III system off the pallet and down the ramp.
7. Roll the system carefully into the operation location and position it for setup.
- III Deskside Workstation 1
- System User’s Guide 1
- Record of Revision 3
- 007-5630-001 vii 7
- 007-5630-001 ix 9
- Contents 10
- List of Figures 11
- 1. Introduction and Overview 13
- Quick Setup Procedures 14
- 007-5630-001 3 15
- Choosing a Site 16
- 007-5630-001 5 17
- 6 007-5630-001 18
- 1: Introduction and Overview 18
- Power-On Problems 19
- System Overview 20
- I/O Panel Overview 21
- Physical Specifications 22
- System Power Supplies 22
- 007-5630-001 11 23
- 12 007-5630-001 24
- Nodeboard Features 25
- Serial ATA 26
- PCI Expansion Slots 26
- Optional Ethernet Ports 26
- Other Features 26
- InfiniBand 27
- 16 007-5630-001 28
- 007-5630-001 17 29
- Troubleshooting the System 30
- System Fan Failure 32
- Rear I/O Connectors 33
- USB Type A Connector 34
- VGA Video Interface 35
- RJ-45 (Ethernet) Connectors 36
- DB9 Serial Connector 37
- DVI-I Video/Monitor Port 38
- Stereo-Sync Connector 39
- 4. BIOS Information 41
- Starting the Setup Utility 42
- Main Setup 42
- System Time/System Update 43
- System Board 43
- Advanced Setup Configurations 44
- Boot Features 45
- Power Configuration 46
- Processor and Clock Options 47
- 36 007-5630-001 48
- 4: BIOS Information 48
- 007-5630-001 37 49
- Advanced Chipset Control 50
- 007-5630-001 39 51
- North Bridge Configuration 52
- SouthBridge Configuration 53
- 42 007-5630-001 54
- IDE and SATA Configuration 55
- 44 007-5630-001 56
- 007-5630-001 45 57
- PCI/PnP Configuration 58
- Remote Access Configuration 59
- 48 007-5630-001 60
- Hardware Health Monitor 61
- 50 007-5630-001 62
- ACPI Configuration 63
- Trusted Computing 64
- IPMI Configuration 65
- View BMC System Event Log 65
- Set LAN Configuration 66
- IP Address Configuration 66
- MAC Address Configuration 67
- Subnet Mask Configuration 67
- SEL PEF Configuration 68
- DMI Event Log 69
- Security Settings 70
- Boot Configuration 71
- Boot Device Priority 72
- Exit Options 73
- Save Changes and Exit 74
- Discard Changes and Exit 74
- BIOS Error Beep Codes 75
- BIOS Error Beep Code List 76
- A. Technical Specifications 77
- Environmental Specifications 78
Produits connexes et manuels pour Serveurs SGI Octane III
Serveurs SGI Altix XE210 Guide de l'utilisateur
(170 pages)
(170 pages)
Serveurs SGI Origin 3900 Guide de l'utilisateur
(144 pages)
(144 pages)
Serveurs SGI UV 2000 Guide de l'utilisateur
(110 pages)
(110 pages)
Serveurs SGI ISS3500 Manuel d'utilisateur
(93 pages)
(93 pages)
(28 pages)
Serveurs SGI C1110-RP6 Manuel d'utilisateur
(30 pages)
(30 pages)
© 2020, manymanuals.fr. Tous droits réservés | 1.936 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels