SGI Rackable C1000 Guide de l'utilisateur Page 54
- Page / 122
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
32 007-5688-001
5: Advanced Severboard Setup
Serverboard Quick Reference
Installing Memory
Caution: Exercise extreme care when installing or removing DIMM modules to prevent any
possible damage.
SGI Rackable C2108-TY10 serverboard supports up to 144 GB of DDR3 1333/1066/800
registered ECC SDRAM in 18 DIMM slots. Three-way interleaved memory is supported. For
optimal memory performance, install DIMMs three at a time. Use memory modules of the same
type and speed. See the following table for memory installation.
Install DIMMs
Perform the following steps to install memory modules, as follows:
1. Insert the DIMM module vertically and press down into its slot until it snaps into place. Pay
attention to the alignnment notch at the bottom of the module to avoid installing incorrectly
(see Figure 5-4 and Figure 5-5). Insert the desired number of DIMMs into the memory slots,
beginning with DIMM #1A and DIMM #2A, then DIMM #3A and DIMM #4A, etc. (see
Table 5-1 Jumper Descripton
Jumper Description Default Setting
JBT1 CMOS Clear See Section 5-10
J12 SMB to PCI-Exp. Slots Pins 2-3 (Disabled)
J13 SMB to PCI-X Slots Pins 2-3 (Disabled)
J21 Watch Dog Enable/Disable Pins 1-2 (Reset)
JP3 IDE Enable/Disable Pins 1-2 (Enabled)
JPG1 VGA Enable/Disable Pins 1-2 (Enable)
JPL1 LAN1/2 Enable/Disable
Pins 1-2 (Enabled)
!
- Rackable™ C2108-TY10 System 1
- User’s Guide 1
- Record of Revision 3
- 007-5688-001 vii 7
- 007-5688-001 ix 9
- Contents 10
- 007-5688-001 xi 11
- 007-5688-001 xiii 13
- 007-5688-001 xv 15
- About This Guide 17
- Related Publications 19
- Conventions 20
- Product Support 20
- Reader Comments 21
- 1. Introduction 23
- 2 007-5688-001 24
- 1: Introduction 24
- Server Board Features 25
- Server Chassis Features 26
- Serial ATA Subsystem 27
- Front Control Panel 27
- Motherboard 27
- Cooling System 27
- 6 007-5688-001 28
- 2. Server Installation 29
- Warnings and Precautions 30
- Rack Mounting Considerations 31
- Circuit Overloading 32
- Reliable Ground 32
- 007-5688-001 11 33
- Outer Rack Rails 34
- Install the Server in a Rack 35
- Check the Node Board Setup 36
- 007-5688-001 15 37
- Check the CPUs (processors) 38
- Check the System Memory 38
- Install Expansion PCI Cards 38
- Check the Drive Bay Setup 38
- Check the Airflow 39
- Supply Power to the System 39
- 3. System Interface 41
- Control Panel LEDs 42
- 007-5688-001 21 43
- SATA Drive Carrier LEDs 44
- 4. System Safety 45
- General Safety Precautions 46
- ESD Precautions 47
- 5. Advanced Severboard Setup 49
- Unpacking 50
- Connecting the Control Panel 50
- I/O Ports 51
- Serverboard Details 52
- Installing Memory 54
- 007-5688-001 33 55
- Figure 5-4 DIMM Installation 55
- 34 007-5688-001 56
- 5: Advanced Severboard Setup 56
- Memory Configuration 57
- Front of Chassis 58
- Rear of Chassis 58
- Memory DIMM Rules 59
- 38 007-5688-001 60
- 007-5688-001 39 61
- 40 007-5688-001 62
- 007-5688-001 41 63
- 42 007-5688-001 64
- 007-5688-001 43 65
- 44 007-5688-001 66
- 007-5688-001 45 67
- PCI Card Slotting 68
- Installing Selected PCI cards 69
- 6. Advanced Chassis Setup 71
- 50 007-5688-001 72
- 6: Advanced Chassis Setup 72
- Static-Sensitive Device 73
- Control Panel 73
- System Fans 74
- Replacing System Fans 75
- Accessing the Drive Bays 75
- SATA Drive Installation 76
- 007-5688-001 55 77
- Removing the Power Supply 79
- Installing a New Power Supply 79
- Starting BIOS Setup Utility 81
- Starting the Setup Utility 82
- Main Setup 82
- System Time/System Update 83
- Serverboard 83
- Advanced Setup Configurations 84
- Boot Features 85
- Power Configuration 86
- Processor and Clock Options 87
- 66 007-5688-001 88
- 007-5688-001 67 89
- Advanced Chipset Control 90
- 007-5688-001 69 91
- North Bridge Configuration 92
- SouthBridge Configuration 93
- 72 007-5688-001 94
- IDE and SATA Configuration 95
- 74 007-5688-001 96
- 007-5688-001 75 97
- PCI/PnP Configuration 98
- Remote Access Configuration 99
- 78 007-5688-001 100
- Hardware Health Monitor 101
- 80 007-5688-001 102
- ACPI Configuration 103
- Trusted Computing 104
- View BMC System Event Log 105
- IPMI Configuration 105
- Set LAN Configuration 106
- IP Address Configuration 106
- MAC Address Configuration 107
- Subnet Mask Configuration 107
- SEL PEF Configuration 108
- DMI Event Log 109
- Security Settings 110
- Boot Configuration 111
- Boot Device Priority 112
- Exit Options 113
- Save Changes and Exit 114
- Discard Changes and Exit 114
- Discard Changes 115
- Load Optimal Defaults 115
- Load Fail-Safe Defaults 115
- A. BIOS Error Codes 117
- B. System Specifications 119
- 98 007-5688-001 120
- B: System Specifications 120
- System Cooling 121
- System Input Requirements 121
- Power Supply 121
- Operating Environment 121
- Regulatory Compliance 122
Produits connexes et manuels pour Serveurs SGI Rackable C1000
Serveurs SGI IS2224 Manuel de service
(114 pages)
(114 pages)
Serveurs SGI 1450 Guide de l'utilisateur
(118 pages)
(118 pages)
Serveurs SGI Virtu VN200 Manuel d'utilisateur
(100 pages)
(100 pages)
Serveurs SGI Altix XE210 Guide de l'utilisateur
(170 pages)
(170 pages)
Serveurs SGI Origin 3900 Guide de l'utilisateur
(144 pages)
(144 pages)
Serveurs SGI UV 2000 Guide de l'utilisateur
(110 pages)
(110 pages)
Serveurs SGI ISS3500 Manuel d'utilisateur
(93 pages)
(93 pages)
(28 pages)
Serveurs SGI C1110-RP6 Manuel d'utilisateur
(30 pages)
(30 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.150 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels